New Arrival Intelligent Programming Charge Power Supply UD-12V2700
Intelligent Power Supply UD-12V2700 Automotive Programming Dedicated Power
1. Can Automatically detect and fix according to the health status of the battery.
2. Can charge the battery inside and outside the car, as well as battery repairing.
3. Can repair kinds of batteries, such as ordinary lead-acid batteries, AGM, GEL, VRLA, and others when charging.
4. Automatic Detection Mode, Charging Mode, Exhibit mode, Programming Mode, Battery Repairing Mode.
5. Constant current charging can be any character set.
1. Intelligent programming charging power supply for energy-saving and environment-friendly, yellow-green-screen backlit digital LCD display, is the latest one with automatic detection, automatic charging, automatic maintenance and smart programming as well as other advanced new charger.
2. Multiple protection and self protection. Power off alarm, heat alarm, overload, overheating, overcharging, short circuit, reverse polarity protection function.
3. Auto battery repairing functions, can detect different types of battery charging rehabilitation, apply to automobile service stations, 4S shop and maintenance workshop of advanced charging equipment.
4. Can be used for static state of the vehicle maintenance, testing and electric control system used during programming set code. Preventing them from car damage and data loss during programming or other tests because of the low power.
5. No spark, applies to all special charging curve of battery technology, in full compliance with vehicle electronic systems and air bag requirements.
Please read this manual carefully before using the product.
Combustible gas will be produced when charging, fire is strictly prohibited at the operating site.
Be careful of the corrosion when it is rainy, snowy or wet. Positive and negative of charge clip cannot be reversed.
Vibration and impact should be avoided, do not charge the frozen battery.
You must use the standard fuse.
Keep the charger clean and check the initial voltage before using it.
Battery charge rules:
Current charging depends on the charge value from the rechargeable battery.
Depends on the battery type, typically calculated according to the following formula:
Ah/=< battery charging current charging time >
In addition, since the continuation of the charging time, the charging current decreases,
so the entire charging process than the numerical extension of the formula 1/4.
This Intelligent Power Supply can charge one or more batteries meantime, but the charging time will be extended accordingly.
When charging the vehicle battery, remove the original battery clamps.
Steps to use this Intelligent Power supply Charger:
1、Connect the battery and charger.
2、Choose the right mode according the actual situation of the battery and the table below, noted, if the mode outside vehicle is chosen, make sure the
battery is out of the car. After finishing this step, press start and the consequential charging will be active.
3、If you connect the battery correctly and it shows poor contact, just press the right button and handle according the tips,
enable the Mode Enforce Charging.
4、In the programming mode, the voltage cannot be adjusted in Mode 2, and it can be adjusted in Mode 1.
Press the Right and Down Button at the same time and you can adjust the voltage using the Up and Down Button after hearing “Beep”
Then press Right and Down Button again to exit the adjust mode. Press start to begin charging.
1、Right / Left
2、Up / Down
5、Over Charge Protection
6、Over Heat Protection
7、Low Voltage Protection
8、Short Circuit Protection
9、Revert Polarity Protection
*Long-press the left key and the right key at the same time to switch between Chinese and English
1pc x Intelligent Programming Charge Power Supply UD-12V2700
Shipping method and delivery time:UK Warehouse Shipping: 2-4 working days
, Only item title marked " Ship from UK " will ship from UK warehouse. ( UK local address 2-4 working days arrival, other European countries will take about 5-10 working days arrival depend on the place), We will pay the freight ship to each customer, If customer country does not have Shipping service in our UK warehouse or only have UPS service, customer need pay the UPS freight difference or package will ship from Shenzhen, China.DHL Shipping: 2-4 working days
, To help you clearance we will help declare a lower price on the invoice help clearance. If address is remote area, customer need pay remote freight or we will ship by Normal Post or Yanwen Express.Yanwen Express: 5-10 working days
, usually No Tax for European Countries or Remote Area . The tax was pre-paid, when package reached, there's no tax no extra fee for customers.
If you have any questions about the device, the price or the payment, please can contact us for free.Contact Person:
13983755934Official Email: Sales@obd2shop.co.ukSkype: OBD2Tool.co.ukOnline service support