Newsletter
AUTEL Maxicom MK908P Technical support
Matched product:
2024 Autel Maxicom MK908 Pro II Scanner J2534 Programming Tool ECU Program Coding 36+ Services Scan VIN and Pre&Post Scan Get Free MV108S
£1,399
- Item No. SP413
- Free Shipping
1) 2024 Autel MK908 PRO II, New Ver. of Maxisys Elite II/MS908S PRO II
2) With advanced J2534 ECU Programming for BENZ & BMW
3) Suppor ECU coding , 36+ hot services &Autoauth, OE-Level Diagnostics & Active Test
UK/EU warehouse shipping, fast delivery no tax!
2) With advanced J2534 ECU Programming for BENZ & BMW
3) Suppor ECU coding , 36+ hot services &Autoauth, OE-Level Diagnostics & Active Test
UK/EU warehouse shipping, fast delivery no tax!
Part 1 Autel MaxiCOM MK908P VCI Manager Operations
1. Connection Mode – there are two connection modes available for selection. The connection state is displayed alongside.
BT Paring – when paired to a wireless device, the connection state displays as Paired; otherwise it displays as Unpaired.
Update (for VCI software only) – updates VCI software via internet through the MaxiCOM tablet networking using USB connection.
Select a connection mode to manage and set up connection.
2. Settings – this section allows you to manage wireless pairing or set up network connection.
BT Setting – searches and displays the type and a partial serial number for all of the devices available for pairing. Tap a required device to start pairing.
The BT status icon displayed to the left of the device name indicates the received signal strength.
Ethernet Setting – allows you to perform network configuration.
Part 2 How to Update Autel MaxiCOM MK908P Firmware
1. Power up the MaxiCOM Display Tablet, and ensure that it is connected to a power source and with steady internet connection.
2. Tap the Update application button from the MaxiCOM Job Menu, or tap the update notification message when received one. The Update application screen displays.
3. Check all available updates:
If you decide to update all the items, tap the Update All button.
If you only want to update some individual items, tap the Update button on the right column of the specific item.
4. Tap the Pause button to suspend the updating process. When you tap Continue to renew the update, the updating process will resume from the break point.
5. When the updating process is completed, the firmware will be installed automatically. The new version will replace the original version if there is one.
Part 3 Autel MaxiCOM MK908P Bluetooth BT Pairing
The VCI device needs to be either connected to a vehicle or to an available power source, so that it is powered up during the synchronization procedure.
Make sure the MaxiCOM Display Tablet has a charged battery or is connected to an AC / DC power supply.
To pair the VCI device with the Display Tablet
1. Power on the MaxiCOM Display Tablet.
2. Connect the 26-pin end of the data cable to the J2534 ECU Programming Device’s vehicle data connector (for MaxiCOM Pro); Or connect the 15-pin end of the data cable to the Wireless BT Diagnostic Interface’s vehicle data connector (for MaxiCOM)
3. Connect the 16-pin end of the data cable to the vehicle data link connector (DLC).
4. Tap the VCI Manager application on the MaxiCOM Job Menu of the display tablet.
5. Select BT from the connection mode list.
6. Tap the Scan button at the top right corner. Now the device starts searching for available pairing units.
7. Depending on the VCI type you use, the device name may display as Maxi suffixed with a serial number. Select the required device for pairing.
8. When paring is successfully done, the connection status displayed to the right of the device name is shown as Paired.
9. Wait a few seconds, and the VCI button on the system Navigation bar at the bottom of the screen shall display a green tick icon, indicating the display tablet is connected to the VCI device.
10. Tap the paired device again to unpair it.
11. Tap the Back button on the top left to return to the MaxiCOM Job Menu.
Part 4 How to Exchange Autel Tablets Language?
MK908P free to exchange language now.
You need to offer the customer service SN.
After we tell you that the language authorization is ok, you can do as following steps:
1. please go “setting” -> “language” -> choose French
2. go “setting” -> “system setting” -> “language and input” -> choose language French
3. reboot the MK808/MK908P tablet
4. go “Update” to download the software again